You apply pre-emergent herbicides before weed seeds germinate, typically in the spring. Pre-emergent herbicides do not prevent weed seeds from germinating; they suppress the development of weed roots as they germinate. They’re usually effective for two weeks to three months, depending on the formulation, and you have to water the lawn after applying for the herbicide for it to be effective. There are pre-emergent herbicides to kill both broadleaf weeds and weedy grasses. You can apply them before you sow your grass seed. If you apply a pre-emergent herbicide that kills weedy grasses, you have to delay sowing your lawn seed.
Fertilizers containing pre-emergent herbicides selectively prevent certain kinds of weeds from finishing their germination cycle. There is no point applying this type of weed-and-feed mix after weeds are growing on your lawn. You have to apply it early in the growing season before weeds appear. Make sure the pre-emergent herbicide in the fertilizer kills the kind of weeds that have plagued your lawn in the past. You might apply a starter fertilizer containing a pre-emergent herbicide before you sow your lawn seeds.
Post emergent herbicides kill weeds after they appear. Some post-emergent, systemic herbicides that you can apply directly on lawns only kill weedy grasses, while others only kill weeds with broadleaf weeds. Contact herbicide such as those including the active ingredient glyphosate kills on contact. To use one of those on a lawn without killing the grass you have to daub it on individual weeds.
You can sow grass seeds now and kill weeds later with a post-emergent herbicide or kill weeds now with a pre-emergent herbicide and plant the seeds later. Weed-and-feed fertilizers are specially formulated combinations of turf fertilizer and herbicides that you apply either before you plant grass seeds or on established lawns.
Post-emergent weed-and-feed formulations kill selective weeds that are already growing in your lawn. Make sure that the herbicide in the formulation you buy kills the type of weeds that are growing in your lawn. Most weeds make their appearance in the spring, the best time to apply weed-and-feed fertilizer.
Weed and feed products consist of fertilizers such as nitrogen or potassium, and a pre-emergent or post-emergent herbicide. If the weed and feed is designed for spring application, it contains a pre-emergent. If it is designed for later in the growing season, it incorporates a post-emergent herbicide. Knowing which one you are using is important because the herbicides affect plants in significantly different ways.
Since weed and feed products are designed to prevent germination — or to eradicate a living plant — they can, for the most part, have a similar effect on young turf grass. The only exception is the pre-emergent herbicide siduron, which is actually used to assist in seed germination. When using a pre-emergent that does not contain siduron, wait a minimum of two months before seeding. If using a product designed for broadleaf weeds, read the label carefully, because the active ingredient in these post-emergent herbicides have a wider range for the waiting period. Grass can be planted in as little as one month after application for products using 2,4-D to as much as six months for atrazine-based products.
How They Work
Pre-emergent weed and feed is applied in early spring so the herbicide is in place before the undesirable weeds germinate. Pre-emergent herbicide works by inhibiting germination. It must be watered with at least one-half inch of water to move the chemical from the surface into the soil. Post-emergent herbicides, however, must be applied while the weeds are actively growing because for the chemical to work, the herbicide must be absorbed into the plant.
You want a beautiful lawn for your family to enjoy, but it’s no longer enough to just mow it. You have to fertilize, water, kill weeds and then reseed any bare spots. Using a weed and feed product saved you some time, so now you’re ready to plant some grass seed. You may have to wait a bit longer, though, depending on the type of weed and feed product you used.
When you are ready to seed your lawn, use a garden rake to remove debris and to break up the surface to ensure the seed comes into contact with the soil. Broadcast the seeds in two directions to ensure complete coverage, and water the ground lightly and often for up to two weeks — keeping the soil moist. Once seedlings have established, gradually reduce the frequency of the watering, but lengthen the amount of time per watering. This will encourage a deep root system for your grass.
Weed and feed fertilizers are often used in combination with seeding. Weed and feed formulations consist of two components: a herbicide to kill weeds and a fertilizer to strengthen the turf. The herbicide will weaken the grass as well as the weeds and the fertilizer will strengthen the weeds as well as the grass. When applying seed over a weed and feed application, remember that some weed and feeds can prevent grass seeds from growing.
It’s important to know a little about herbicides so you can make the best choice for when to apply seed in an area that has been treated for weeds. The most common types of herbicide in weed and feed products are selective and systemic. Selective herbicides target a species of plant to kill while systemic herbicides work by being absorbed though the roots and then transported throughout the plant, killing it from within. Read the bag label to see what kind of herbicide is used in the weed and feed you are considering using or have used. The bag label will tell you how many days you must wait before applying seed to a lawn that has been treated with that product.
Types of Herbicide
Only use a weed and feed if the weed infestation is completely uniform over the entire lawn and all species of weeds targeted will be affected by the herbicide in the weed and feed. This scenario doesn’t occur often, so it is more likely the use of an herbicide and a fertilizer separately will be needed. If the weeds are uniformly spread over the area to be treated, match the appropriate weed and feed product to your grass, the seed you have recently applied or want to apply, and the time of year.
Herbicides can target weeds before they germinate from seed – pre-emergent – or as developed plants – post-emergent. Before you seed, you can use a non-selective, post-emergent herbicide to control any weeds in the area to be seeded. Most of these can be applied up to two weeks before seeding to control any existing weeds. Herbicides should not be used after seeding until the new seedlings are established. Mowing and spot treatments can be used to control weeds until the seeded area is actively growing and requires only maintenance watering. Establishment times vary depending on the type of seed you use and your weather conditions.
It is important to know what kind of grass you have growing or want to have growing. Certain chemicals act differently on different species of grass and weeds. For example, the common herbicide 2,4-D is toxic to some cultivars of St. Augustine grass (Stenotaphrum secundatum), which grows in the area roughly covered by U.S. Department of Agriculture plant hardiness zones 8 through 10. Another common herbicide, atrazine, is potentially lethal to grass when applied in temperatures above 85 degrees Fahrenheit. Use the instructions on the bag of each weed and feed product to determine how it will affect seeding.