Weed and feed fertilizers are often used in combination with seeding. Weed and feed formulations consist of two components: a herbicide to kill weeds and a fertilizer to strengthen the turf. The herbicide will weaken the grass as well as the weeds and the fertilizer will strengthen the weeds as well as the grass. When applying seed over a weed and feed application, remember that some weed and feeds can prevent grass seeds from growing.
Only use a weed and feed if the weed infestation is completely uniform over the entire lawn and all species of weeds targeted will be affected by the herbicide in the weed and feed. This scenario doesn’t occur often, so it is more likely the use of an herbicide and a fertilizer separately will be needed. If the weeds are uniformly spread over the area to be treated, match the appropriate weed and feed product to your grass, the seed you have recently applied or want to apply, and the time of year.
Types of Herbicide
Herbicides can target weeds before they germinate from seed – pre-emergent – or as developed plants – post-emergent. Before you seed, you can use a non-selective, post-emergent herbicide to control any weeds in the area to be seeded. Most of these can be applied up to two weeks before seeding to control any existing weeds. Herbicides should not be used after seeding until the new seedlings are established. Mowing and spot treatments can be used to control weeds until the seeded area is actively growing and requires only maintenance watering. Establishment times vary depending on the type of seed you use and your weather conditions.
It is important to know what kind of grass you have growing or want to have growing. Certain chemicals act differently on different species of grass and weeds. For example, the common herbicide 2,4-D is toxic to some cultivars of St. Augustine grass (Stenotaphrum secundatum), which grows in the area roughly covered by U.S. Department of Agriculture plant hardiness zones 8 through 10. Another common herbicide, atrazine, is potentially lethal to grass when applied in temperatures above 85 degrees Fahrenheit. Use the instructions on the bag of each weed and feed product to determine how it will affect seeding.
It’s important to know a little about herbicides so you can make the best choice for when to apply seed in an area that has been treated for weeds. The most common types of herbicide in weed and feed products are selective and systemic. Selective herbicides target a species of plant to kill while systemic herbicides work by being absorbed though the roots and then transported throughout the plant, killing it from within. Read the bag label to see what kind of herbicide is used in the weed and feed you are considering using or have used. The bag label will tell you how many days you must wait before applying seed to a lawn that has been treated with that product.
Although this can be frustrating and we can appreciate that a quick solution will be desired, the good news about these types of weeds is that they are largely shallow rooting and should come out with the first mow at the 6-8 week mark after sowing. If they don’t, they should be easy to pull out of the turf.
However, you can get rid of these weeds just as fast as they have appeared.
The important thing to remember when new weeds appear in your newly sown lawn is not to act hastily – do not apply a Feed, Weed and Moss Killer type product of any kind on a newly sown lawn.
If you find that the weeds are recurring past the 6-8-week mark, you may wish to consider using a selective herbicide to spot spray your weeds. Some weed killers such as glyphosate (Roundup) kill more than just weeds, so it is important to not apply these as if they are not done precisely, they can kill your grass. Shop bought selective weed killers will recommend when to apply their product and how often and you should read the instructions thoroughly and adhere to them.
In short, here’s what you should do if you encounter weeds in your newly seeded lawn:
If you find that when the lawn is at least six months old and has been taken over by weeds or moss, you can use a Feed, Weed and Moss Killer product.
A general rule of thumb is to wait at least until you have mowed the new grass four times before using any standard postemergent broadleaf herbicide. A standard pre-emergent herbicide should not be applied until at least three to four months after seeding the area.
Some pre-emergent herbicides can safely be used during seeding and usually come mixed with a seed starter. These products have the active ingredient Siduron – also known as Tupersan – that works by suppressing weed seeds while improving root development of the new grass. The fertilizer and pre-emergent herbicide mix is applied with a drop or rotary spreader using a rate of 2 1/2 pounds per 1,000 square feet. The spreader setting and actual application depends on the brand of starter fertilizer plus weed control you use, and you should always follow the instructions found on the label.
Before you plant grass seed, you should always prepare the area by removing any weeds that may be growing in the location. Even with careful preparation of the planting site, weeds can still develop among the newly planted grass seed. Weed killers, however, can harm grass seeds and seedlings if applied too early or improperly.
Weed management should be completed before seeding the lawn with a non-selective herbicide seven to 14 days before you till the soil. A second application of the herbicide may be required to kill any weeds you missed during the first treatment. Wait another seven days until tilling the soil if a second application is used.
Remember that all herbicides are different and the exact time you must wait to apply weed killers to newly planted grass will vary from one product to another. Also, some herbicides cannot be applied to certain species of turfgrass. For best results, always refer to the herbicide bottle’s label.